manualshive.com logo in svg

Altera PHY IP Core, User Manual

Share
Download
Altera PHY IP Core User Manual Download Page 173

Chapter 10: Transceiver Reconfiguration Controller

10–7

Interfaces

March 2012

Altera Corporation

Altera Transceiver PHY IP Core

User Guide

Interfaces

This section describes interfaces for the Transceiver Reconfiguration Controller. 

Figure 10–2

 illustrates the top-level signals of the Transceiver Reconfiguration 

Controller.

1

By default, the 

Block Diagram

 shown in the parameter editor labels the external pins 

with the 

interface type

 and places the

 interface name

 inside the box. The interface type 

and name are used in the Hardware Component Description File (

_hw.tcl

). If you 

click 

Show signals

, the block diagram expands to show all of the signals of the 

component given the options currently selected in the parameter editor. 

f

For more information about 

_hw.tcl

 files refer to the 

Component Interface Tcl Reference

 

in volume 1 of the 

Quartus II Handbook

.

MIF Reconfiguration Management Avalon-MM Master Interface

Table 10–5

 describes the signals that comprise the dynamic reconfiguration interface. 

The Transceiver Reconfiguration Controller communicates with the PHY IP cores 
using this interface.

Figure 10–2. Top-Level Signals of the Transceiver Reconfiguration Controller

Transceiver Reconfiguration Controller Top-Level Signals

Reconfiguration

Management 

Avalon-MM Slave

Interface

MIF Reconfiguration

Avalon-MM Master

Interface

Transceiver 

Reconfiguration

reconfig_mif_address[31:0]
reconfig_mif_read
reconfig_mif_readdata[15:0]
reconfig_mif_waitrequest

mgmt_clk_clk
mgmt_rst_reset
reconfig_mgmt_address[6:0]
reconfig_mgmt_writedata[31:0]
reconfig_mgmt_readdata[31:0]
reconfig_mgmt_write
reconfig_mgmt_read
reconfig_mgmt_waitrequest

reconfig_to_xcvr[(

<n>

70-1):0]

reconfig_from_xcvr[(

<n>

46-1):0]

reconfig_busy

Table 10–5. MIF Reconfiguration Management Avalon-MM Master Interface

Signal Name

Direction

Description

reconfig_mif_address[31:0]

Output

This is the Avalon-MM address. This is a byte address.

reconfig_mif_read

Output

When asserted, signals an Avalon-MM read request.

reconfig_mif_readdata[15:0]

Input

The read data.

reconfig_mif_waitrequest

Input

When asserted, indicates that the MIF Avalon-MM slave is not 
ready to respond to a read request.

Summary of Contents for PHY IP Core







































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands