manualshive.com logo in svg

Altera PHY IP Core, User Manual

Share
Download
Altera PHY IP Core User Manual Download Page 119

Chapter 7: Custom PHY IP Core

7–19

Interfaces

March 2012

Altera Corporation

Altera Transceiver PHY IP Core

User Guide

Reset Control and Status (Optional)

Table 7–19

 describes the signals in the optional reset control and status interface. 

These signals are available if you do not enable the embedded reset controller. For 
more information including timing diagrams, refer to 

Transceiver Reset Control in 

Stratix V Devices

 in volume 3 of the 

Stratix V Device Handbook

.

rx_syncstatus[

<n>

(

<w>/<s>

)-1:0]

Output

Indicates presence or absence of synchronization on the RX 
interface. Asserted when word aligner identifies the word 
alignment pattern or synchronization code groups in the received 
data stream. This signal is optional.

rx_is_lockedtoref[

<n>

-1:0]

Output

Asserted when the receiver CDR is locked to the input reference 
clock. This signal is asynchronous. This signal is optional.

rx_is_lockedtodata[

<n>

-1:0]

Output

When asserted, the receiver CDR is in to lock-to-data mode. 
When deasserted, the receiver CDR lock mode depends on the 

rx_locktorefclk

 signal level. This signal is optional.

rx_signaldetect[

<n>

-1:0]

Output

Signal threshold detect indicator required for the PCI Express 
protocol. When asserted, it indicates that the signal present at the 
receiver input buffer is above the programmed signal detection 
threshold value. 

rx_bitslip[

<n>

-1:0]

Input

Used for manual control of bit slipping. The word aligner slips a 
bit of the current word for every rising edge of this signal.

rx_bitslipboundaryselectout

[

<n>

5-1:0]

Output

This signal is used for bit slip word alignment mode. It reports 
the number of bits that the RX block slipped to achieve a 
deterministic latency. 

rx_patterndetect

[

<n>

(

<w>/<s>

)-1:0]

Output

When asserted, indicates that the programmed word alignment 
pattern has been detected in the current word boundary. 

rx_rmfifodatainserted[

<n>

-1:0]

Output

When asserted, indicates that the RX rate match block inserted an 
||R|| column.

rx_rmfifodatadeleted[

<n>

-1:0]

Output

When asserted, indicates that the RX rate match block deleted an 
||R|| column.

rx_rlv[

<n>

-1:0]

Output

When asserted, indicates a run length violation. Asserted if the 
number of consecutive 1s or 0s exceeds the number specified in 
the parameter editor. 

rx_recovered_clk[

<n>

-1:0]

Output

This is the RX clock which is recovered from the received data 
stream. 

No

t

e 

t

o 

Table 7–17

:

(1) <n> is the number of lanes. 

<w>

 is the PCS to FPGA fabric interface width per lane. 

<s>

 is the symbol size in bits. 

<p>

 is the number of PLLs.

Table 7–18. Serial Interface and Status Signals  (Part 2 of 2)

(1)

Signal Name

Direction

Signal Name

Table 7–19. Avalon-ST RX Interface  (Part 1 of 2)

Signal Name

Direction

Description

pll_powerdown

Input

When asserted, resets the TX PLL. 

tx_digitalreset[

<n>

-1:0]

Input

When asserted, reset all blocks in the TX PCS.

tx_analogreset[

<n>

-1:0]

Input

When asserted, resets all blocks in the TX PMA.

tx_cal_busy[

<n>

-1:0]

>

Output

When asserted, indicates that the TX channel is being calibrated. You 
must hold the channel in reset until calibration completes.

Summary of Contents for PHY IP Core







































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands