Altera PHY IP Core User Manual Download Page 33

Page: 33 / 230

Chapter 3: 10GBASE-R PHY IP Core

3–15

Interfaces

March 2012

Altera Corporation

Altera Transceiver PHY IP Core

User Guide

The PCS runs at 257.8125 MHz using the

pma_rx_clock

provided by the PMA. You

must provide the PMA a input reference clock running at 644.53725 MHz to generate
the 257.8125 MHz clock.

Figure 3–4

illustrates the clock generation and distribution

for Stratix IV devices.

Figure 3–4. Stratix IV GT Clock Generation and Distribution

pll_ref_clk

644.53125 MHz

10.3125

Gbps serial

516.625

MHz

257.8125

MHz

516.625

MHz

257.8125

MHz

156.25 MHz

10GBASE-R Transceiver Channel - Stratix IV GT

TX PCS

(hard IP)

TX PCS

(soft IP)

TX PMA

10.3125

Gbps serial

RX PCS

(hard IP)

RX PCS

(soft IP)

RX PMA

5/4

TX PLL

8/33

GPLL

xgmii_rx_clk

xgmii_tx_clk

Summary of Contents for PHY IP Core







































































































































































































































Search results

Summary of Contents for PHY IP Core

Reviews:

Brands by name

Popular brands

Altera PHY IP Core, User Manual

Search results

Summary of Contents for PHY IP Core

Reviews:

Brands by name

Popular brands