Alpha Data XRM(2)-DAC-D4/1G User Manual Download Page 32

Page: 32 / 92

XRM(2)-DAC-D4/1G User Guide

V2.2 - Mar 8, 2018

4.1 FPGA_CNTRL_REG (0x00)

The control register provides various bits for controlling timing and resets.

D31 to D24:

D31 Clock align request, rising edge triggers alignment.

D30 Select HF DCM when low (default), LF DCM when high.

D29 Q channel signal select bit 2

D28 I channel signal select bit 2

D27 Unused.

D26 Sync enable for I DAC and QDAC.

D25 Clock mux control msb.

D24 Clock mux control lsb.

D23 to D16:

D23 'GPIO_N' port direction signal, 1=output, 0=default=input.

D22 'GPIO_N 'port output signal.

D21 'GPIO_P' port direction signal, 1=output, 0=default=input.

D20 'GPIO_P' port output signal.

D19 'AUX' port direction signal, 1=output, 0=default=input.

D18 'AUX' port output signal.

D17 'TRIG' port direction signal, 1=output, 0=default=input.

D16 'TRIG' port output signal.

D15 to D8:

D15 Alignment reset signal,1=reset active.

D14 Q channel FPGA data generator reset (1=reset active).

D13 I channel FPGA data generator reset (1=reset active).

D12 QDAC hardware reset, 1=reset active.

D11 IDAC hardware reset, 1=reset active.

D10

Determines DLL bypass bit in initialisation sequence (0=default=DLL
enabled).

VCXO oscillator enable (1 = oscillator running).

100MHz reference oscillator enable (1 = oscillator running).

D7 to D0:

Q channel signal select bit 1

Q channel signal select bit 0

Q channel signal select bit 3, msb

Q channel output enable; 0=all zeroes transmitted, 1=FPGA
generator data transmitted to DAC.

I channel signal select bit 1

Page 28

Register Description

xrm-dac-d4-1g-manual_v2_2.pdf

Summary of Contents for XRM(2)-DAC-D4/1G





























































































Search results

Summary of Contents for XRM(2)-DAC-D4/1G

Reviews:

Brands by name

Popular brands

Alpha Data XRM(2)-DAC-D4/1G, User Manual

Search results

Summary of Contents for XRM(2)-DAC-D4/1G

Reviews:

Brands by name

Popular brands