manualshive.com logo in svg

Alpha Data XRM(2)-DAC-D4/1G, User Manual

Share
Download
Alpha Data XRM(2)-DAC-D4/1G User Manual Download Page 30

XRM(2)-DAC-D4/1G User Guide

V2.2 - Mar 8, 2018

4 Register Description

All data accesses are 32 bits wide; for writes, unused bits are ignored whilst on reads unused bits are always

mapped as a logic low.

A total of 30 registers are used, although not all bits are active controls.

Register Name

Address

CNTRL_REG

0X00

STATUS_REG

0X01

CNTR_STATUS_REG

0X02

I_DDS_REG

0X03

Q_DDS_REG

0X04

I_INC_REG

0X05

Q_INC_REG

0X06

SYNTH_CNTRL_REG

0X07

SYNTH_STRB_REG

0X08

IDAC_CNTRL_REG

0X09

IDAC_STRB_REG

0X0A

QDAC_CNTRL_REG

0X0B

QDAC_STRB_REG

0X0C

DEVICE_REG

0X0D

I_DDSINIT_REG

0X0E

Q_DDSINIT_REG

0X0F

IPATTERN_REG

0X10

QPATTERN_REG

0X11

IPATTERN_REG2

0X12

QPATTERN_REG2

0X13

MEAS0_VAL_REG

0X14

MEAS1_VAL_REG

0X15

MEAS2_VAL_REG

0X16

FREERUN_CNT_REG

0X17

I_ARBWRITE_REG

0X18

Q_ARBWRITE_REG

0X19

ARB _CNTRL_REG

0X1A

ARB _TICK_REG

0X1B

Not used

0X1C

Not used

0X1D

AUXCNTRL_REG

0X1E

Page 26

Register Description

xrm-dac-d4-1g-manual_v2_2.pdf

Summary of Contents for XRM(2)-DAC-D4/1G





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands