AirLive POE-200CAM V2 User Manual Download Page 53

Page: 53 / 117

AirLive

POE

‐

200CAMv2

User’s

Manual

【

Step1

】

By selecting DNS Setting button

from the Menu Bar, you may specify the Domain

Name Server.

【

Step2

】

If your computer gets IP from DHCP

service or its IP changes periodically due to the

policy of your network administrator, please check

“Enable DNS resolution”, so any alert message

could be delivered to AirLive CamPro Express from

camera no matter what IP your server is assigned.

Enter the Domain Name your computer registered to

“DNS of this PC” field.

【

Note

】

Please request a DNS for AirLive CamPro

Express from your MIS.

Storage

By selecting Storage button

from the Menu Bar, you may configure the storage and recycling rule.

There is two different areas, namely area 1 (include path1 and storage1) and area 2 (include path2 and

storage2):

Area 1: is assigned the disk to store recorded data.

Area 2: is assigned for the backup purpose, it is an optional service.

Summary of Contents for POE-200CAM V2






















































































































Search results

Summary of Contents for POE-200CAM V2

Reviews:

Related manuals for POE-200CAM V2

Brands by name

Popular brands

AirLive POE-200CAM V2, User Manual

Search results

Summary of Contents for POE-200CAM V2

Reviews:

Related manuals for POE-200CAM V2

Brands by name

Popular brands