AirLive POE-200CAM V2 User Manual Download Page 16

Page: 16 / 117

AirLive

POE

‐

200CAMv2

User’s

Manual

appear. Click

to proceed

;

the network indicator on the device will start to blink. After completing adjustments

to the default settings, the device will reboot automatically. Do not turn off the device until the device reboots.

Backup setting data

：

Save the setting data of the device to a file. Click

Save

, and follow the instructions on the

browser to save the setting data file to your specified location.

Restore setting

：

Load the saved setting data of the device. Click

Browse

and select the file in which the setting

data is stored. Click

, and the device is adjusted according to the loaded data and restarted.

Firmware update

：

Upgrade the device software. Click

Browse

and select the file for upgrading. A confirmation

dialogue will appear. Click

to start upgrading. The device will reboot upon completion.

Note:

• Use only upgraded files that are special for this device. Problems may occur otherwise.

• Do not turn off the device power or disconnect the network until the upgrading is completed.

Upload language pack

：

Upgrade the device language pack. Click

Browse

and select the file for upgrading. A

confirmation dialogue will appear. Click

to start upgrading. The upgrade is applied immediately. The default

language is “

English.

”

6.1.2 Camera

6.1.3 General

RTSP:

Switch the RTSP streaming On/Off.

Note

：

•

RTSP:

Real Time Streaming Protocol. RTSP is supported by most of the media clients. (RealPlayer,

Media Player, QuickTime, etc…)

Image Rotate

：

Enables user to mirror or flip the display screen.

Night Mode

：

Turn Night Mode ON/OFF.

Lighting

：

Choose the lighting environment among 50Hz, 60Hz and Outdoor.

White Balance

：

Choose the White Balance to Auto, Fluorescent, Incandescent and Black&White.

Summary of Contents for POE-200CAM V2






















































































































Search results

Summary of Contents for POE-200CAM V2

Reviews:

Related manuals for POE-200CAM V2

Brands by name

Popular brands

AirLive POE-200CAM V2, User Manual

Search results

Summary of Contents for POE-200CAM V2

Reviews:

Related manuals for POE-200CAM V2

Brands by name

Popular brands