AirLive POE-200CAM V2 User Manual Download Page 76

Page: 76 / 117

AirLive

POE200CAMv2

User’s

Manual

【

Note

】

When to configure?

AirLive CamPro Express system default are same as device default, only when you want to change PW from

AirLive CamPro Express or when you find the PW of device has been changed in web configuration program

Sensor (Digital Input)

Many video gateways and LAN cameras has GPIO port. The digital inputs can be connected to sensors, while

digital outputs can be connecting to relay switches.

In System Setup tree, a sensor is represented by

(un-configured sensor) or

(configured sensor)

icon, and relay switch is represented by

icon.

When you select a sensor in the System Setup tree, the toolbar becomes:

But the two buttons on the right will appear only after a sensor has been configured.

Sensor Setting

Click the [Sensor Setting] button to bring up the Sensor Setting dialog, as shown below:

Summary of Contents for POE-200CAM V2






















































































































Search results

Summary of Contents for POE-200CAM V2

Reviews:

Related manuals for POE-200CAM V2

Brands by name

Popular brands

AirLive POE-200CAM V2, User Manual

Search results

Summary of Contents for POE-200CAM V2

Reviews:

Related manuals for POE-200CAM V2

Brands by name

Popular brands