Agilent Technologies 4395A, Manual Change

Page: 473 / 575

Front P anel K ey Description
4 Cal 5 Continued
NA/ZA Standard type menu
????????????????????????????????????
STD TYPE: OPEN Denes the standard type as an OPEN (used for calibrating reection measurements). OPENs are
assigned a terminal impedance of innite ohms (but delay and loss osets can still be added).
Pressing this key also displays a menu for dening the OPEN (including its capacitance).
??????
C0 Enters the C
0
term, which is the constant term of the quadratic equation and is scaled by 10
015
F arads .
??????
C1 Enters the C
1
term, expressed in F/Hz (F arads/Hz) and scaled by 10
027
.
??????
C2 Enters the C
2
term, expressed in F/Hz
2
and scaled by 10
036
.
??????????????????????????????????
SPECIFY OFFSET ! NA/ZA
Specify oset menu
Displays the specify oset menu that denes osets in delay , loss , and standard impedance (Z
0
) for
each standard type .
????????????????????????
LABEL STD Displays the letter menu to dene a label for each standard.
?
???????????????????????????????????????????
STD DONE (DEFINED) T erminates the standard denition. Press this after each standard is dened (including osets).
?????????????
SHORT Denes the standard type as a SHORT , for calibrating reection measurements . SHORT s are
assigned a terminal impedance of 0 . However , delay and loss osets can still be added.
? ?????????????????????????????????
SPECIFY OFFSET ! NA/ZA
Specify oset menu
Displays the specify oset menu that denes osets in delay , loss , and standard impedance (Z
0
) for
each standard type .
????????????????????????
LABEL STD Displays the letter menu to dene a label for each standard.
????????????????????????????????????????????
STD DONE (DEFINED) T erminates the standard denition. Press this after each standard is dened (including osets).
? ???????????
LO AD Denes the standard type as a LO AD (termination). LO ADs are assigned a terminal impedance
equal to the system characteristic impedance Z
0
. However , delay and loss osets can still be
added. If the LO AD impedance is not Z
0
, use the arbitrary impedance standard denition.
? ?????????????????????????????????
SPECIFY OFFSET ! NA/ZA
Specify oset menu
Displays the specify oset menu that denes osets in delay , loss , and standard impedance (Z
0
) for
each standard type .
????????????????????????
LABEL STD Displays the letter menu to dene a label for each standard.
????????????????????????????????????????????
STD DONE (DEFINED) T erminates the standard denition. Press this after each standard is dened (including osets).
?????????????????????????
DELA Y/THRU Denes the standard type as a transmission line of specied length, for calibrating transmission
measurements .
? ?????????????????????????????????
SPECIFY OFFSET ! NA/ZA
Specify oset menu
Displays the specify oset menu that denes osets in delay , loss , and standard impedance (Z
0
) for
each standard type .
????????????????????????
LABEL STD Displays the letter menu to dene a label for each standard.
? ???????????????????????????????????????????
STD DONE (DEFINED) T erminates the standard denition. Press this after each standard is dened (including osets).
????????????????????????????????????????????????
ARBITRARY IMPED ANCE Denes the standard type to be a LO AD with an arbitrary impedance (dierent from system Z
0
).
??????????????????????????????????????????????
TERMINAL IMPED ANCE Species the (arbitrary) impedance of the standard in ohms .
??????????????????????????????????
SPECIFY OFFSET ! NA/ZA
Specify oset menu
Displays the specify oset menu that denes osets in delay , loss , and standard impedance (Z
0
) for
each standard type .
????????????????????????
LABEL STD Displays the letter menu to dene a label for each standard.
? ???????????????????????????????????????????
STD DONE (DEFINED) T erminates the standard denition. Press this after each standard is dened (including osets).
?????????????????
RETURN
Softkey Reference B-25