![background image](http://html1.mh-extra.com/html/advantech/adam-4021/adam-4021_user-manual_2856815037.webp)
25
ADAM-4000 Series User Manual
C
ha
pte
r 3
I/O
M
od
ule
s
3.2.2
Technical specification of ADAM-4015
Table 3.1: Technical Specification of ADAM-4015
Channel Number
6 differential
Support Protocol
ADAM ASCII and MODBUS/RTU
Input Type
Pt100, Pt1000, BALCO500, Ni
Input Connections
2 or 3 wires
Wire Burnout Detection Yes
Input Type and Tem
-
perature Range
Pt100: -50 to 150° C
0 to 100° C
0 to 200° C
0 to 400° C
-200 to 200° C
Pt1000: -40 to 160° C
Balco500: -30 to 120° C
Ni(518): -80~100° C
0~100° C
Ni(508): 0~100° C
-50~200° C
BA1: -200~600° C
Isolation Voltage
3000 V
DC
Sampling Rate
10 sample/second (total)
Input Impedance
10 MΩ
Resolution
16-bit
Accuracy
±0.1% (Typical)
CMR@50/60Hz
120 dB
NMR@50/60Hz
100 dB
Span Drift
± 25 ppm/°C
Zero Drift
± 6 μV/°C
Watchdog Timer
System (1.6 second) and Communication
Power Input
+10~+30 V
DC
(non-regulated)
Power Consumption
Typical: 0.5 W @ 24 V
DC
Max.: 0.9 W @ 24 V
DC
ADAM-4015
RTD type
Temperature Range
Accuracy
Platinum 100 (IEC)
-50 ~ 150°C
0 ~ 100°C
0 ~ 200°C
0 ~ 400°C
-200 ~ 200°C
0.10%
Platinum 100 (JIS)
-50 ~ 150°C
0 ~ 100°C
0 ~ 200°C
0 ~ 400°C
-200 ~ 200°C
0.2% or better
Platinum 1000
-40 ~ 160°C
0.10%
BALCO 500
-30 ~ 120°C
0.50%
Ni 508
-50 ~ 200°C
0.10%
Summary of Contents for Adam - 4021
