225
ADAM-4000 Series User Manual
Ap
pe
nd
ix B
D
ata
F
orm
ats
a
nd
I/O
R
an
ge
s
B.1.4
Ohms
To indicate ohms, set bits 0 and 1 of the data format/checksum/integration time
parameter to 11.
The ohms format allows you to read the value of the RTD resistance in ohms. It con
-
sists of a “+” or “-” sign followed by five decimal digits and a decimal point. The reso
-
lution (position of the decimal point) of Platinum-Nickel RTDs is 10 m Ω. (two decimal
places).
For example, a 100 Ω platinum RTD specified for -100°C to +100°C has +100°C cor
-
responding to +138.50 Ω and -100o C corresponding to +060.60 Ω.
The measurable resistance values are as given below:
The format is
Type, Bottom Tem. (ohm) ~ Top Temp. (ohm)
BA1
-200(7.95) ~ 600(145.85)
PT-100 (0.385)
-50(80.31) ~ +150(157.31)
PT-100 (0.392)
-50(79.96) ~ +150(158.29)
PT-100 (0.385)
0(100.00) ~ +100(138.50)
PT-100 (0.392)
0(100.00) ~ +100(139.16)
PT-100 (0.385)
0(100.00) ~ +200(175.84)
PT-100 (0.392)
0(100.00) ~ +200(177.13)
PT-100 (0.385)
0(100.00) ~ +400(247.04)
PT-100 (0.392)
0(100.00) ~ +400(249.56)
PT-100 (0.385)
-200(18.49) ~ +200(175.84)
PT-100 (0.392)
-200(18.49) ~ +200(177.13)
PT-1000
-40(842.7) ~ +160(1610.4)
Balco-500
-30(397.05) ~ +120(723.44)
Ni604-518
-80(410.73) ~ +100(917.33)
Ni604-518
0(604) ~ +100(917.33)
Ni508A
0(507) ~ 100(772)
Ni508B
-50(400.14) ~ 200(1099.89)
Summary of Contents for Adam - 4021
