![background image](http://html1.mh-extra.com/html/advantech/adam-4021/adam-4021_user-manual_2856815087.webp)
75
ADAM-4000 Series User Manual
C
ha
pte
r 4
C
om
m
an
d S
et
Table 4.8: ADAM-4021 Command Table
Command Syntax Command Name
Command Description
Page No.
%AANNTTCCFF
Configuration
Set the address, output range, baud
rate, data format, slew rate and/or
checksum status
6-3
#AA(data)
Analog Data Out
Directs output data to a specified
module
6-6
$AA4
Start-up output cur
-
rent/voltage configu
-
ration
Stores a default output value in a
specified module. The output value
will take effect upon startup.
6-8
$AA3(number of
counts)
Trim Calibration
Trims specified module a number of
units up/down
6-9
$AA0
4 mA Calibration
Tells the module to store parameters
for 4 mA Calibration
6-11
$AA1
20 mA Calibration
Tells the module to store parameters
for 20 mA Calibration
6-12
$AA2
Configuration Status Reads configuration of specified
module
6-13
$AA6
Last Value Readback
Returns either last value sent to spec
-
ified module by #AA command, or
start-up output current/voltage
6-14
$AA8
Current Readback
Returns measured value of the cur
-
rent/voltage flowing through current
loop
6-15
$AA5
Reset Status
Checks if module has been reset
since the last $AA5 command
6-16
$AAF
Read Firmware Ver
-
sion
Return the firmware version code
from the specified analog output
module
6-17
$AAM
Read Module Name Return the module name from the
specified analog output module
6-18
Summary of Contents for Adam - 4021
