![background image](http://html1.mh-extra.com/html/advantech/adam-4021/adam-4021_user-manual_2856815088.webp)
ADAM-4000 Series User Manual
76
Table 4.9: ADAM-4024 Command Table
Command Syntax Command Name
Command Description
Page No.
%AANNTTCCFF
Configuration
Set the address, output range, baud
rate, data format, slew rate and/or
checksum status
6-19
#AACn(data)
Analog Data Out
Directs output data to a specified
module
6-20
#AASCn(data)
Set Startup Data
Set data As CHn StartUp Data
6-20
#AAECn(data)
Set Emergency Stop Set data As CHn Emergency Stop
Data
6-20
#**
N/A
Synchrous Sample IDI
6-20
$AA0Cn
4 mA Calibration
Tells the module to store parameters
for 4 mA Calibration
6-20
$AA1Cn
20 mA Calibration
Tells the module to store parameters
for 20 mA Calibration
6-20
$AA2
Configuration Status Read back Module status
6-20
$AA3Cn(number of
counts)
Trim Calibration
Trims specified module a number of
units up/down
6-20
$AA4
Start-up output cur
-
rent/voltage configu
-
ration
Stores a default output value in a
specified module. The output value
will take effect upon startup.
6-20
$AA5
Reset Status
Read Back Reset Times After Last
$AA5 CMD And Clear This ounter
6-20
$AA6Cn
Last Value Readback
Returns either last value sent to spec
-
ified module by #AA command, or
start-up output current/voltage
6-20
$AA7CnRxx
Set Output Type
Set CHn Output Type
6-20
$AA8Cn
Current Readback
Returns measured value of the cur
-
rent/voltage flowing through current
loop
6-21
$AAF
Read Firmware
Version
Return the firmware version code
from the specified analog output
module
6-21
$AAM
Read Module Name Return the module name from the
specified analog output module
6-21
$AAACnZ
EMS Flag setting
Enable/Disable (Z=1/0)
CHn EMS Flag
6-21
$AABCn
Read EMS Flag
Read CHn EMS Flag
6-21
$AADCn
Read startup data
Read Back CHn StartUp Data
6-21
$AAECn
Read emergency
Stop
Read Back CHn Emergency Stop
Data
6-21
$AAG
Reset Current Trim
Reset Current Trim Data Variable To
0
6-21
$AAH
Read Current Trim
Read Current Trim Data Variable
6-21
$AAI
Read IDI
Read IDI
6-21
$AANCn
Read 4mA Calibra
-
tion Parameter
Read Back CHn 4mA Calibration
Parameter
6-21
$AAOCn
Read 20mA Calibra
-
tion Parameter
Read Back CHn 20mA Calibration
Parameter
6-21
Summary of Contents for Adam - 4021
