ADB Safegate AXON User Manual Download Page 44

Page: 44 / 88

Note

Refer to the

Open and close a 12

‑

inch Fixture

section.

2. Disconnect the cable:

a) Disconnect the secondary cable from the converter by placing a small flat-head screwdriver into the opening located

at the other side of the secondary wire, and

b) Release the cable by prying the screwdriver on the cable release opening.

3. Unscrew the Strain-relief Bolt and its plate.

Make sure you dispose the old Strain-relief Bolt and its plate and use the new material.

4. Unscrew the Strain Relief Bolt, the plate and the cable gland gaskets.

Make sure you dispose the old Strain Relief Bolt, the plate and the cable gland gaskets and use the new material.

5. Remove the secondary cable

Make sure you dispose the old secondary cable and use the new secondary cable.

6. Mount the new cable gland gaskets.
7. Replacement:

a) Pull the secondary wires through the Strain-relief Plate and the cable gland gaskets and

b) Mount the new secondary cable by torquing the new Strain-relief Bolt at.XX in-lbs (XX Nm).

8. Locking:

a) Lock the secondary cables leading to the converter by opening the cable holes prying a thin screwdriver on the cable

release opening and mounting the wires in place and

b) Lock the cables by releasing screwdriver from the opening.

9. Close the light.

Note

Refer to the

Open and close an 8

‑

inch Fixture

section.

5.3.10 Reset the Fail-open Converter

Parts

•

Fuse resistor spare part kit: 20210209 (20 pcs)

Info

•

Converter with 1 connector have 2 fuse resistors

•

Converter with 2 connectors have 4 fuse resistors

Reset / replace the fuse resistors

1. Disconnect and disassemble the light fixture.
2. Locate the fuse resistors.

Note

Refer to

Figure 8

and

Figure 9

figures.

AXON Runway Inset Lights
Maintenance

34
Copyright

Summary of Contents for AXON


















































































Search results

Summary of Contents for AXON

Reviews:

Related manuals for AXON

Brands by name

Popular brands

ADB Safegate AXON, User Manual

Search results

Summary of Contents for AXON

Reviews:

Related manuals for AXON

Brands by name

Popular brands