manualshive.com logo in svg

ADB Safegate AXON, User Manual

Share
Download
ADB Safegate AXON User Manual Download Page 4

Note

See your sales order contract for a complete warranty description.
Replaced or repaired equipment under warranty falls into the warranty of the original delivery. No new warranty

period is started for these replaced or repaired products.

Liability

WARNING

Use of the equipment in ways other than described in the catalog leaflet and the manual may result in personal injury,

death, or property and equipment damage. Use this equipment only as described in the manual.

ADB SAFEGATE cannot be held responsible for injuries or damages resulting from non-standard, unintended uses of its

equipment. The equipment is designed and intended only for the purpose described in the manual. Uses not described in the

manual are considered unintended uses and may result in serious personal injury, death or property damage.
Unintended uses, includes the following actions:

•

Making changes to equipment that have not been recommended or described in this manual or using parts that are not

genuine ADB SAFEGATE replacement parts or accessories.

•

Failing to make sure that auxiliary equipment complies with approval agency requirements, local codes, and all applicable

safety standards if not in contradiction with the general rules.

•

Using materials or auxiliary equipment that are inappropriate or incompatible with your ADB SAFEGATE equipment.

•

Allowing unskilled personnel to perform any task on or with the equipment.

©

 ADB SAFEGATE BV

This manual or parts thereof may not be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,

electronic, mechanical, photocopying, recording, nor otherwise, without ADB SAFEGATE BV's prior written consent.
This manual could contain technical inaccuracies or typographical errors. ADB SAFEGATE BV reserves the right to revise this

manual from time to time in the contents thereof without obligation of ADB SAFEGATE BV to notify any person of such

revision or change. Details and values given in this manual are average values and have been compiled with care. They are

not binding, however, and ADB SAFEGATE BV disclaims any liability for damages or detriments suffered as a result of reliance

on the information given herein or the use of products, processes or equipment to which this manual refers. No warranty is

made that the use of the information or of the products, processes or equipment to which this manual refers will not infringe

any third party's patents or rights. The information given does not release the buyer from making their own experiments and

tests.

AXON Runway Inset Lights

iv
Copyright 

©

 ADB Safegate, All Rights Reserved

Summary of Contents for AXON

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands