ADB Safegate AXON User Manual Download Page 43

Page: 43 / 88

Note

Refer to the

5.3.8 Replace the secondary Cable — SJO cord set

Tools to be used:

•

Screwdriver T25 bit

•

Flat-head screwdriver

•

Small flat head screwdriver

1. Open the light.

Note

Refer to the

Open and close a 12

‑

inch Fixture

section.

2. Disconnect the cable:

a) Disconnect the secondary cable from the converter by placing a small flat-head screwdriver into the opening located

at the other side of the secondary wire, and

b) Release the cable by prying the screwdriver on the cable release opening.

3. Unscrew the Strain-relief Bolt and its plate.

Make sure you dispose the old Strain-relief Bolt and its plate and use the new material.

4. Unscrew the cable clamp.

Make sure you dispose the old bolt, washer and lock washer and use the new material.

5. Remove the secondary cable

Make sure you dispose the old secondary cable and use the new secondary cable.

6. Replacement:

a) Pull the secondary wires through the Strain-relief Plate and

b) Mount the new secondary cable by torquing the new strain relief bolt at XX in-lbs XX Nm.

7. Tighten the new cable clamp bolt with the washer and lock washer at XX in-lbs XX Nm.
8. Locking:

a) Lock the secondary cables into the converter by opening the cable holes prying a thin screw driver on the cable

release opening and mounting the wires in place

b) Lock the cables by releasing screw driver from the opening.

9. Close the light.

Note

Refer to the

5.3.9 Replace the secondary Cable — Style-6 cord set

Tools to be used:

•

Screwdriver T25 bit

•

Flat-head screwdriver

•

Small flat head screwdriver

1. Open the light.

UM-5055, Rev. 1.0.9, 2022/04/29

Summary of Contents for AXON


















































































Search results

Summary of Contents for AXON

Reviews:

Related manuals for AXON

Brands by name

Popular brands

ADB Safegate AXON, User Manual

Search results

Summary of Contents for AXON

Reviews:

Related manuals for AXON

Brands by name

Popular brands