ADB Safegate AXON User Manual Download Page 63

Page: 63 / 88

6.5 Ordering Code LED L-852G(L) Runway Guard Light (RG)

Ordering Code

Application

RG = L-852(L) Runway Guard Light

Standards

3 = ICAO

1,2

Market Specific

0 = None

1 = Buy American Preference

Dimensions

1 = 8 inch (203 mm) diameter

2 = 12 inch (305 mm) diameter, 11.25 inch

BC (285 mm)

3 = 8 inch (203 mm) diameter, 4-bolt

Prism

S = Standard prism

R = Reinforced prism

Beam Orientation

1 = Unidirectional

Toe-in

N = None

Color (Side 1 – Left)

Y = Yellow

Color (Side 2 – Right)

N = None

Power and Monitoring

M = 2.8 A - 6.6 A Fail-Open monitoring

5,7

R = 2.8 A - 6.6 A, ILCMS integrated OFDM EQ

A = 2.8 A - 6.6 A, ILCMS EQ Integrated Autonomous

Operation - RGL only

Cable and Connector

1 = 1 x Style 6 2-pole plug, 2 individual wires

2 = 1 x Style 1 2-pole plug, jacketed SO 2 core cable

5 = 1 x flat 3-pole plug, 3 individual wires

Options

0 = None

1 = Arctic Kit

Version Control

1 = Version 1

Ordering Code Notes

Fixture supports: Compatible with both shallow and deep 12-inch bases.
EQ light fixtures are only available as a one connector option.

Option 3 covers standards: NATO,EASA,STAC,TP-312,MOS 139.

50-Hz applications

FAA applications

UM-5055, Rev. 1.0.9, 2022/04/29

Summary of Contents for AXON


















































































Search results

Summary of Contents for AXON

Reviews:

Related manuals for AXON

Brands by name

Popular brands

ADB Safegate AXON, User Manual

Search results

Summary of Contents for AXON

Reviews:

Related manuals for AXON

Brands by name

Popular brands