ADB Safegate AXON User Manual Download Page 39

Page: 39 / 88

5. Disconnect the wires:

a) Pull carefully to disconnect the wires between the converter and the light engine.

b) Pull carefully to disconnect the wires between the converter and the heater kit(s), if the heater kit is in place.

6. Remove the gasket between the Top Cover Assembly and the Inner Pan Assembly.

Make sure you dispose the old gasket and use a new gasket.

5.3.2 Close a Light Fixture — connect the Bottom Pan to the Top Cover

Tools to be used:

•

Screwdriver T25 bit

•

Flat-head screwdriver

1. Clean all the contact surfaces of the light fixture and of the housing carefully.
2. Press the gasket ( located between top cover and inner pan) into the O-ring Groove.

Make sure the gasket placed correctly.

Important

The O-ring Gasket must always be changed when the fixture is being disassembled.

3. Connect the wires:

a) Press carefully to connect the wires lead in from the light engine on the converter.

b) Press carefully to connect the wires lead in from the light engine on the converter, if the heater kit is in place.

4. Put the Top Cover onto the Bottom Pan.

Make sure the poke-yoke (alignment pin) is in the placed correctly.

Important

Do not pinch the wires or the gasket.

5. Put the light fixture on a surface with the top cover facing down.
6. Torque:

a) Use new fixation screws to torque in star pattern at 31 in-lbs (3.5 Nm).

b) Retorque the screws in star pattern at 31 in-lbs (3.5 Nm).

7. Follow the water-tightness test procedure.

Note

Refer to the

Check the Light Fixture for Water-tightness

section.

5.3.3 Replace the Wire Harnesses

Tools to be used:

•

Screwdriver T20 bit

1. Open the light.

Note

Refer to the

Open and close a 12

‑

inch Fixture

section.

2. Remove the LED brackets (3 pieces M5 screws per bracket) to access the connector of the LED wire.

Make sure you dispose the old screws and use new screws.

UM-5055, Rev. 1.0.9, 2022/04/29

Summary of Contents for AXON


















































































Search results

Summary of Contents for AXON

Reviews:

Brands by name

Popular brands

ADB Safegate AXON, User Manual

Search results

Summary of Contents for AXON

Reviews:

Brands by name

Popular brands