ADB Safegate AXON User Manual Download Page 17

Page: 17 / 88

3.0 Introduction

The all-in-one solution
The 12

‑

inch and 8-inch range is a bi- or unidirectional low protrusion light-emitting diode (LED) inset light fixture, available in

multiple versions:

Non-MON

Basic operation providing power only

MON (Fail-open) A LED light fixture with integrated fail open technology with CCR monitoring compatibility

Fixture with integrated ILCMS remote utilizing orthogonal frequency-division multiplexing (OFDM) technology

providing superior communication interfacing with LINC 360 System.

NOTICE

All our Axon R-series light fixtures are equipped with failed LED detection monitoring as required by FAA Engineering Brief 67.

Runway Inset 12"

Runway Inset 8"

Runway Inset 12" with
Style-1 jacketed cord set

Runway Inset 12" with
Style-6 cord set

Runway Inset 8" with
Style-1 jacketed cord set

Runway Inset 8" with
Style-6 cord set

Note

EQ light fixtures are not fail-open light fixtures. The monitoring as well as the control functionality is handled by the ILCMS system.

UM-5055, Rev. 1.0.9, 2022/04/29

Summary of Contents for AXON


















































































Search results

Summary of Contents for AXON

Reviews:

Related manuals for AXON

Brands by name

Popular brands

ADB Safegate AXON, User Manual

Search results

Summary of Contents for AXON

Reviews:

Related manuals for AXON

Brands by name

Popular brands