ADB Safegate AXON User Manual Download Page 26 | Manualshive

Page: 26 / 88

background image

4.3 Installation and Removal of the 12-inch Light Fixture

Install the light fixture in a base

1. Carefully clean all contact surfaces of the light fixture and the base.
2. Put the O-ring gasket in the gasket track on the base.

Note

Not for class 2.

3. Connect the connector(s) of the light fixture to the base supply cable(s). Check that the A- and B-side are connected to

corresponding circuit if two connectors are used.

4. Place the connector under the light fixture and install in the base.
5. For an installation on bases, use a torque limiting box spanner of 16/17 mm, install and tighten the six fixing bolts or

nuts to a torque value according to specification, see

INTEROPERABILITY

. For other base manufacturers, refer to their

specifications.

Note

Do not use high speed for tightening, the recommended speed is 10

‑

40 rpm.

6. After installation, make sure that each light fixture functions properly.
7. In order to bond the light fixture to ground, use the supplied screw (Torx M4×6 mm, Torque 2.5Nm) to attach the braided

ground strap to the grounding point on the light fixture. The grounding point is indicated by a grounding symbol and

located on the bottom side.

Remove the fitting from the base

CAUTION

Fall- and trip hazard! When a light fixture has been removed, the base must be fitted with a cover designed for this

purpose or with a spare light fixture.

1. Remove the light fixture from the base using two large flat blade screwdrivers.
2. Disconnect the secondary supply connector.
3. Remove and check the gasket (O-ring or labyrinth).

Note

It is recommended to change the gasket, lock nuts or bolts each time the light fixture is removed or dismounted from

the base. For more information, see

INTEROPERABILITY

AXON Runway Inset Lights
Installation

16
Copyright

©

ADB Safegate, All Rights Reserved

«
...
24
25
26
27
28
...
»

Summary of Contents for AXON

























































































Reviews:

No comments

Related manuals for AXON

Brand: XTA Pages: 29

Brand: vc999 Pages: 59

Brand: Qtx Pages: 3

Brand: Saferoad Pages: 24

Brand: Radarcan Pages: 40

Brand: vanEE Pages: 52

Brand: Caddon Hives Pages: 3

Brand: Raven Pages: 17

Brand: Campbell Pages: 12

Brand: Garden Treasures Pages: 2

Brand: U-Line Pages: 6

Brand: VaBroom Pages: 4

Brand: Rigol Pages: 12

Brand: Landoll Pages: 144

Brand: Castellini Pages: 299

Brand: Lowenstein Medical Pages: 457

GrainLogix XLB10

Brand: LOFTNESS Pages: 104

Brand: Joyolight Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands