ADB Safegate AXON User Manual Download Page 62

Page: 62 / 88

Ordering Code Notes

Includes NATO, EASA, STAC, TP-312, MOS 139

If 2-cord set fixture, digit 13 must be M

Bidirectional application - Place the required color option in Side 1 (Left) and 2 (Right). Left and right side determined by

viewing fixture from runway centerline. Unidirectional application - Side 1 only, choosing left or right for correct toeing.

Arctic Kit not needed

Arctic Kit when necessary

2-cord set option available

All Style 1 corded fixtures will include a ground lug. All Style 6 or 3-pole corded fixtures will be provided without a ground

lug UNLESS digit 6 is option 1 "BAP".

Only available in digit 13 options S and M and bi-directional configuration

Not valid option for uni-directional

Red and Green require Arctic Kit

AXON Runway Inset Lights
Spare Parts

52
Copyright

Summary of Contents for AXON


















































































Search results

Summary of Contents for AXON

Reviews:

Related manuals for AXON

Brands by name

Popular brands

ADB Safegate AXON, User Manual

Search results

Summary of Contents for AXON

Reviews:

Related manuals for AXON

Brands by name

Popular brands