ADB Safegate AXON User Manual Download Page 69

Page: 69 / 88

6.8 Ordering Code LED L-850E(L) Threshold (RR)

Ordering Code

RS
Application

RR = L-850E(L) Threshold

Standard

2 = FAA

4 = Other - NAVAIR

Market Specific

0 = None

Dimensions

2 = 12 inch (305 mm), diameter 11.25 inch

BC (285 mm)

Prism

S = Standard prism

R = Reinforced prism

Beam Orientation

1 = Unidirectional

Toe-in

N = None

Color (Side 1 - Left)

W = White

F = F-Green

R = Red

Color (Side 2 - Right)

N = None

Power and Monitoring

S = 2.8 A - 6.6 A, Non-Monitored - Power Only

M = 2.8 A - 6.6 A, Fail-open monitoring

R = 2.8 A - 6.6 A, ILCMS integrated OFDM EQ

Connector and Cable

2 = 1 x Style 1 2-pole plug, jacketed SO 2-core cable

Options

0 = None

1 = Arctic Kit

Version Control

1 = Version 1

Ordering Code Notes

Provided with ground lug

Required for NAVAIR Green only

For White and Red

Digit 5 must be 4.

Digit 5 must be 2.

UM-5055, Rev. 1.0.9, 2022/04/29

Summary of Contents for AXON


















































































Search results

Summary of Contents for AXON

Reviews:

Brands by name

Popular brands

ADB Safegate AXON, User Manual

Search results

Summary of Contents for AXON

Reviews:

Brands by name

Popular brands