ADB Safegate AXON User Manual Download Page 73

Page: 73 / 88

6.12 Ordering Code LED Runway Threshold Wingbar (RW ICAO)

Ordering Code

Application

RW = Runway Wingbar

Standards

3 = ICAO

Market Specific

0 = None

4 = German MIL 7-step FO

Dimensions

2 = 12 inch (305 mm) diameter, 11.25 inch

BC (285 mm)

Prism

S = Standard prism

R = Reinforced prism

Beam Orientation

1 = Unidirectional

Toe-in

N = None

L = Left

R = Right

Color (Side 1 – Left)

F = F-Green

Color (Side 2 – Right)

N = None

Power and Monitoring

S = 2.8 A - 6.6 A non-monitored - power only

M = 2.8 A - 6.6 A Fail-Open monitoring

R = 2.8 A - 6.6 A ILCMS integrated OFDM EQ

Cable and Connector

1 = 1 x Style 6 2-pole plug, 2 individual wires

2 = 1 x Style 1 2-pole plug, jacketed SO 2 core cable

5 = 1 x flat 3-pole plug, 3 individual wires

Options

0 = None

1 = Arctic Kit

Version Control

1 = Version 1

Ordering Code Notes

Fixture supports: Compatible with both shallow and deep 12-inch bases.
EQ light fixtures are only available as a one connector option.

Option 3 covers standards: NATO,EASA,STAC,TP-312,MOS 139.

L and R designations are always in relationship to Side 1 only.

All Style 1 corded fixtures will include a ground lug. All Style 6 or 3-pole corded fixtures will be provided without a ground

lug.

UM-5055, Rev. 1.0.9, 2022/04/29

Summary of Contents for AXON


















































































Search results

Summary of Contents for AXON

Reviews:

Related manuals for AXON

Brands by name

Popular brands

ADB Safegate AXON, User Manual

Search results

Summary of Contents for AXON

Reviews:

Related manuals for AXON

Brands by name

Popular brands