ADB Safegate AXON User Manual Download Page 45

Page: 45 / 88

Refer to Figure.

Figure 8: Converter 1

Figure 9: Converter 2

Figures 1 and 2

3. Remove the fuse resistors by pulling away from the converter.

a. For converters with 1 connector, always replace both fuse resistors at the same time.

b. For converters with 2 connectors, always replace both fuse resistors related to the A/B channel that needs to be reset.

Make sure you replace all 4 fuse resistors, if both A and B channel needs a reset.

4. Dispose the old fuse resistor.
5. Place the legs of the new fuse resistors in the sockets.
6. Assemble the light fixture and perform a functional test.

5.3.11 Check the Light Fixture for Water-tightness

Tools to be used:

•

Flat head screwdriver

Execute the following procedure to test for leaks:

1. Remove the Pressure-relief Screw.

Refer to the image below.

UM-5055, Rev. 1.0.9, 2022/04/29

Summary of Contents for AXON


















































































Search results

Summary of Contents for AXON

Reviews:

Related manuals for AXON

Brands by name

Popular brands

ADB Safegate AXON, User Manual

Search results

Summary of Contents for AXON

Reviews:

Related manuals for AXON

Brands by name

Popular brands