ABB i-bus VC/S 4 1 Series Product Manual Download Page 138

Page: 138 / 199

ABB i-bus® KNX

PARAMETERS

7.4.144

Valve purge

This parameter is used to define how the valve purge is activated.

More information: → ⁠

Valve purge, Page ⁠⁠190

Option

Deactivated

Valve purge is deactivated.

Automatic or via group object

Valve purge takes place automatically in a set cycle. Valve purge can be triggered via a group object as
well.

The following dependent parameters are shown:
•

Purge cycle in weeks

•

Reset purge cycle from control value greater than or equal to

•

Send value of group object "Status valve purge"

The following dependent group objects are displayed:
•

Status Valve purge X

•

Activate valve purge X

Via group object

The valve purge can be triggered via a group object.

The following dependent parameters are shown:
•

Send value of group object "Status valve purge"

The following dependent group objects are displayed:
•

Status Valve purge X

•

Activate valve purge X

Prerequisites for visibility

\ Parameter

\ Options

Thermoelectric (PWM)

Open/close signal

• The parameter is in the parameter window

Channel X

\ parameter window

Valve output X

7.4.145

Send value group object "In operation"

This parameter is used to define the value that the group object

In operation

sends.

Option

Value 0

Value 1

Prerequisites for visibility

• Parameter window

Basic settings

\ Parameter

Enable group object "In operation"

\ Option

Yes

• The parameter is in the parameter window

Basic settings

7.4.146

Send value of group object "Status valve purge"

This parameter is used to define when the value of the following group object is sent on the bus
(ABB i-bus® KNX):
•

Status Valve purge X

Note

Sending on request can be triggered by the reception of a telegram with the value 0 or 1 on group ob-
ject

Request status values

Product manual | EN-US | VC/S 4.x.1 | 2CDC508220D0211 Rev. B

138

Note about navigation in the PDF: Key combination 'Alt + left arrow'
jumps to the previous view/page

Summary of Contents for i-bus VC/S 4 1 Series








































































































































































































Search results

Summary of Contents for i-bus VC/S 4 1 Series

Reviews:

ABB i-bus VC/S 4 1 Series, Product Manual, Page: 138 / 199

Search results

Summary of Contents for i-bus VC/S 4 1 Series

Reviews: