ABB i-bus VC/S 4 1 Series Product Manual Download Page 95

Page: 95 / 199

ABB i-bus® KNX

PARAMETERS

7.4.68

Cable length, single distance

This parameter is used to set the one-way cable length between sensor and device input.

Option

1.0 … 10.0 … 100.0 m

Prerequisites for visibility

– Parameter

Option

Temperature sensor

– Parameter

Cable error compensation

Option

Via cable length

• The parameter is in the parameter window

Channel X

\ parameter window

Input x

7.4.69

Cable error compensation

This parameter is used to define how cable errors that occur are compensated.

Note

Cable error compensation based on the cable length is possible only for cables with copper conduc-
tors.

Option

None

Cable error compensation is not used.

Via cable length

The following dependent parameters are shown:
•

Cable length, single distance

•

Cross-section of conductor, value* 0.01 mm²

Via cable resistance

The following dependent parameters are shown:
•

Cable resistance (total of fwd and rtn conductor)

Prerequisites for visibility

\ Option

Temperature

sensor

• The parameter is in the parameter window

Channel X

\ parameter window

Input x

7.4.70

Cable resistance (total of fwd and rtn conductor)

This parameter is used to set the cable resistance of the temperature sensor connected.

Note

To measure the cable resistance correctly, the conductors must be shorted together at the cable end
and must not be connected to the input.

Option

0 … 500 … 10,000 mohms

Prerequisites for visibility

– Parameter

Option

Temperature sensor

– Parameter

Cable error compensation

Option

Via cable resistance

• The parameter is in the parameter window

Channel X

\ parameter window

Input x

Product manual | EN-US | VC/S 4.x.1 | 2CDC508220D0211 Rev. B

Note about navigation in the PDF: Key combination 'Alt + left arrow'
jumps to the previous view/page

Summary of Contents for i-bus VC/S 4 1 Series








































































































































































































Search results

Summary of Contents for i-bus VC/S 4 1 Series

Reviews:

ABB i-bus VC/S 4 1 Series, Product Manual, Page: 95 / 199

Search results

Summary of Contents for i-bus VC/S 4 1 Series

Reviews: