manualshive.com logo in svg

ABB i-bus VC/S 4 1 Series, Product Manual, Page: 75 / 199

Share
Download
ABB i-bus VC/S 4 1 Series Product Manual Download Page 75

ABB i-bus® KNX 

PARAMETERS

7.4.34

Input

This parameter is used to define the use of the input.

Note

If, in the parameter 

Connect analog room control unit to physical device input a

, the option 

Yes

 is se-

lected, the option 

Analog room control unit

 is set for this input and cannot be changed.

Note

The inputs are scanned after bus voltage recovery, download or ETS reset. Scanning takes place once
the device functions properly again after download, ETS reset or bus voltage recovery. This can take up
to 2 seconds. The current status is sent on the bus (ABB i-bus® KNX) after the end of the sending and
switching delay.
For binary inputs, the scanning can be defined in the parameter 

Scan input after download, ETS reset

or bus voltage recovery

.

Product manual | EN-US | VC/S 4.x.1 | 2CDC508220D0211 Rev. B  

75

Note about navigation in the PDF: Key combination 'Alt + left arrow'
jumps to the previous view/page

Summary of Contents for i-bus VC/S 4 1 Series








































































































































































































Reviews:

No comments