manualshive.com logo in svg

ABB FBIP-21 BACnet/IP, User Manual

Share
Download
ABB FBIP-21 BACnet/IP User Manual Download Page 67

Note: These settings are available only through web pages. When you select to disable
the web page, a warning appears to confirm before you can save the selection.

Or, you can use the web page password. See

Enable web page access after it was

disabled (page 70)

.

It is recommended to disable all services that are not used after commissioning.

Configuring SNTP

Simple Network Time Protocol (SNTP) can be used to synchronize drive time with a
network time server. When SNTP is enabled, FBIP-21 will request the time from
configured server at a given interval. To receive this time synchronization, you must
configure the drive with parameter 96.20 time sync primary source. The table below
shows the settings for SNTP:

Value

Description

Settings

Default: 30 seconds

Interval to request time from server.

SNTP update interval

Minimum: 30
seconds

-1440...1440
minutes

Time offset to the time received from SNTP.

Note: SNTP time offset change does not need a
reboot.

SNTP time offset to UTC

Appendix C - FBIP-21 configuration web pages 67

Summary of Contents for FBIP-21 BACnet/IP











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands