ABB FBIP-21 BACnet/IP User Manual Download Page 54

Page: 54 / 74

General conditions

Into an option slot on the drive control unit

Installation

IP20

Degree of protection

The ambient conditions specified for the drive in its manuals are applicable.

Ambient conditions

Cardboard. Plastic wrapping: Antistatic air bubble sheet (PE).

Package

Three bicolor LEDs (HOST, MODULE, NETWORK/NET)

Indicators

A 20-pin connector to the drive

Connectors

RJ-45 connector to Ethernet (X1)

RJ-45 connector for chaining another adapter module (X2)

+3.3 V ±5% max. 400 mA (supplied by the drive)

Power supply

Complies with EMC standard EN 61800-3:2004

Compliance

Printed circuit board conformal coated

BACnet link

Ethernet Standard IEEE 802.3 and IEEE 802.3u devices

Compatible devices

10BASE-TX or 100Base-TX with Autonegotiation and Auto-MDIX (Auto-cros-
sover)

Medium

• Wiring: CAT5/6 UTP, CAT5/6 FTP, CAT5/6 STP
• Connector: RJ-45
• Termination: Internal
• Maximum segment length: 100 m / 328 ft

Bus or star.

Topology

Max. 50 nodes allowed for FBIP-21 in a daisy chain topology.

10 Mbps or 100 Mbps.

Transfer rate

Half or full duplex

Serial communication
type

BACnet/IP

Protocol

TCP and UDP service ports

There are multiple in-bound and out-bound network services running on the FBIP-21.

Purpose

Service

Port

DHCP client.

DHCP

68 (UDP)

Note: Used only when IP configuration
method is selected as Dyn IP HFCP.

BACnet IP protocol.

BACnet

47808 (UDP)

Open source licenses

54 Technical data

Summary of Contents for FBIP-21 BACnet/IP










































































Search results

Summary of Contents for FBIP-21 BACnet/IP

Reviews:

Brands by name

Popular brands

ABB FBIP-21 BACnet/IP, User Manual

Search results

Summary of Contents for FBIP-21 BACnet/IP

Reviews:

Brands by name

Popular brands