manualshive.com logo in svg

ABB FBIP-21 BACnet/IP, User Manual

Share
Download
ABB FBIP-21 BACnet/IP User Manual Download Page 52

Function

Color

Name

Establishing communication to host

Blinking green

HOST

Connection to host OK

Green

Communication to host lost temporarily

Blinking red

Internal file system error. The error may be cleared by cycling drive
power. If the error persists, contact your local ABB representative.

Flashing orange, al-
ternating with the
MODULE flashing
orange

There is no power applied to the device.

Off

MODULE

Device is attempting to obtain IP configuration from the DHCP
server.

Flashing orange

Device is executing Duplicate Address Detection.

Orange

Device is waiting for a BACnet request.

Flashing green

Device has received a BACnet request within the timeout period.

Green

Ethernet link is down.

Flashing red

• Ethernet interface is disabled.
• Duplicate Address Detection may have detected a duplicate

address. Check the IP configuration and either initiate a Fieldbus
Adapter parameter refresh or cycle power to the drive.

or

• Drive is not supported by FBIP-21.

Red

Internal file system error. The error may be cleared by cycling drive
power. If the error persists, contact your local ABB representative.

Flashing orange, al-
ternating with the
HOST flashing or-
ange

Device is in boot mode, ready for firmware update (HOST led is
Off).

Flashing red/green

BACnet link is down.

Off

NETWORK /
NET

BACnet link is up at 100 Mbps.

Flashing green

Flashing indicates activity on interface.

BACnet link is up at 10 Mbps. Flashing indicates activity on interface.

Flashing orange

52 Diagnostics

Summary of Contents for FBIP-21 BACnet/IP











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands