manualshive.com logo in svg

ABB FBIP-21 BACnet/IP, User Manual

Share
Download
ABB FBIP-21 BACnet/IP User Manual Download Page 61

Configuration status

No.

After restore

Before restore

Replacing a fieldbus adapter with another adapter of the same type. But the new adapter
was used with some other drive previously.

3

Drive backup is used in FBIP-21.

Drive has a backup of FBIP-21 configuration
and a new FBIP-21 with existing configuration
is attached.

A new drive and fieldbus adapter are used.

4

FBIP-21 generates a new backup with its de-
fault settings and copies it to drive.

Drive has no backup or a backup of some
other type of fieldbus adapter other than FBIP-
21 exists.

FBIP-21 with no configuration is attached.

Replacing drive with a new drive and reusing the old Fieldbus adapter.

5

FBIP-21 copies its backup to drive.

Drive has no backup or a backup of some
other type of fieldbus adapter other than FBIP-
21 exists.

FBIP-21 with an existing configuration is at-
tached.

Clearing fieldbus configuration from drive and module to defaults.

6

Clears the fieldbus parameters and backup
files for FBA A and FBA B on the drive side. If
a FBIP-21 module is connected, its configura-
tions are reset to defaults.

You can clear the fieldbus configuration from
drive and module to defaults with parameter
96.06 Parameter restore using the selection
Reset all fieldbus settings.

Appendix B - Module configuration backup 61

Summary of Contents for FBIP-21 BACnet/IP











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands