AAA RT40 Operator'S Manual Download Page 81

Page: 81 / 165

Plow - 80

RT40 Operator’s Manual

Operation

CMW

Operation

Crushing weight could cause death or serious injury. Use proper

procedures and equipment or stay away.

Electrical shock. Contacting electrical lines will cause death or serious

injury. Know location of lines and stay away.

NOTICE:

Cutting high voltage cable can cause electrocution. Expose lines by hand before digging.

Incorrect procedures could result in death, injury, or property damage.

Learn to use equipment correctly.

NOTICE:

•

Comply with all utility notification regulations before digging or drilling.

•

Notify companies that do not subscribe to One-Call.

•

Do not drive backward with plow in the ground.

*Always follow manufacturer instructions*

*AAA Rent-All 225-291-1356*

Summary of Contents for RT40






































































































































































Search results

Summary of Contents for RT40

Reviews:

Related manuals for RT40

Brands by name

Popular brands

AAA RT40, Operator'S Manual

Search results

Summary of Contents for RT40

Reviews:

Related manuals for RT40

Brands by name

Popular brands