manualshive.com logo in svg

AAA RT40, Operator'S Manual

Share
Download
AAA RT40 Operator'S Manual Download Page 70

RT40 Operator’s Manual

Transport - 69

Tow

CMW

Tow

Under normal conditions, tractor should not be towed. If tractor becomes disabled and towing is 
necessary:

•

Do not tow for more than 200 yd (180 m).

•

Tow at less than 1 mph (1.6 km/h).

•

Use maximum towing force of 1.5 times unit weight.

Procedure 

1.

Attach tow line to all available tiedown points facing towing vehicle.

2.

Bypass hydraulic system.

Remove tunnel cover and loosen bypass valve two 
turns. Valve is on left rear of front pump.

3.

Fasten seat belt.

4.

Disengage parking brake.

5.

Check that ground drive and attachment speed/
direction controls are in neutral position.

Incorrect procedures could result in death, injury, or property damage. 

Learn to use equipment correctly.

Incorrect procedures could result in death, injury, or property damage. 

Learn to use equipment correctly.

t14om051h.eps

*Always follow manufacturer instructions*

*AAA Rent-All 225-291-1356*

Summary of Contents for RT40






































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands