manualshive.com logo in svg

AAA RT40, Operator'S Manual

Share
Download
AAA RT40 Operator'S Manual Download Page 138

RT40 Operator’s Manual

Service - 137

As Needed

Trencher

Replace Digging Chain

Visually check digging chains for wear on rollers and sidebars (2). Check pins (3) and bushing wear by 
measuring distance between chain pins and comparing it with a new chain. Also check digging teeth (1). 

 

To remove chain:

1.

Fasten and adjust seat belt.

2.

Start tractor. See page 62 for proper start-up 
procedures.

3.

Move attachment direction/speed control until 
digging chain connector pin is on top of boom.

4.

Lower boom to ground.

5.

Engage parking brake.

6.

Turn ignition switch to STOP.

7.

Roller booms:

 

Secure chain by clamping links on 

either side of connector pin with chain jaws 
(shown). Squeeze jaws to reduce pressure on 
connector pin.

Sprocket booms: Lock rear idler sprocket.

IMPORTANT: 

Replace sprockets when a new chain is installed.

t12om089h.eps

*Always follow manufacturer instructions*

*AAA Rent-All 225-291-1356*

Summary of Contents for RT40






































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands