AAA RT40 Operator'S Manual Download Page 45

Page: 45 / 165

Controls - 44

RT40 Operator’s Manual

Backhoe Console

CMW

Seat latch

To release backhoe seat,
disengage lock by moving
hole in latch clear of bolt.

IMPORTANT:

Ensure seat is latched

before driving unit.

See “Backhoe” on page 89 for more
information.

Neutral switch

To move tractor, press switch,
use bucket/dipper control to
move tractor, and release
switch.

Mechanical stow lock
control

To lock, push stow lock
handle.

To unlock, move stow lock
handle to right.

Use this control to lock boom in the
stowed position.

NOTICE:

Always lock boom during

transport.

10. Work light switch

To turn on, press right.

To turn off, press left.

Item

Description

Notes

c00ic269h.eps

*Always follow manufacturer instructions*

*AAA Rent-All 225-291-1356*

Summary of Contents for RT40






































































































































































Search results

Summary of Contents for RT40

Reviews:

Related manuals for RT40

Brands by name

Popular brands

AAA RT40, Operator'S Manual

Search results

Summary of Contents for RT40

Reviews:

Related manuals for RT40

Brands by name

Popular brands