manualshive.com logo in svg

AAA RT40, Operator'S Manual

Share
Download
AAA RT40 Operator'S Manual Download Page 109

Service - 108

RT40 Operator’s Manual

Service Precautions

Service Precautions   

Welding Precaution

Cleaning Precaution

Incorrect procedures could result in death, injury, or property damage. 

Learn to use equipment correctly.

NOTICES:

•

Unless otherwise instructed, all service should be performed with engine off.

•

Refer to engine manufacturer’s manual for engine maintenance instructions.

•

Before servicing equipment, lower unstowed attachments to ground.

NOTICE: 

Welding can damage electronics.

•

Disconnect battery at battery disconnect switch before welding to prevent damage to battery. 
Do not turn off battery disconnect switch with engine running or alternator and other electronic 
devices may be damaged.

•

Connect welder ground clamp close to welding point and make sure no electronic components 
are in the ground path.

•

Always disconnect the ECU ground connection from the frame, harness connections to the ECU, 
and other electronic components prior to welding on machine or attachments.

NOTICE: 

When cleaning equipment, do not spray electrical components with water.

*Always follow manufacturer instructions*

*AAA Rent-All 225-291-1356*

Summary of Contents for RT40






































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands