manualshive.com logo in svg

AAA RT40, Operator'S Manual

Share
Download
AAA RT40 Operator'S Manual Download Page 68

RT40 Operator’s Manual

Transport - 67

Haul

CMW

Load

1.

Fasten and adjust seat belt.

2.

Start tractor. See page 58 for proper start-up procedures.

3.

Raise attachments, but keep them low.

4.

Move attachments to center position and check that they are not in float.

5.

Release parking brake.

6.

Slowly drive tractor onto trailer.

7.

Position tractor on trailer deck for proper weight distribution.

8.

Engage parking brake.

9.

Lower attachments to trailer bed and turn tractor off. See page 60 for proper shutdown procedures.

10. Attach chains to tractor and attachments where tiedown decals are located. See page 65.

Crushing weight. If load falls or moves it could kill or crush you. Use 

proper procedures and equipment or stay away.

NOTICE: 

 

•

Attach trailer to tow vehicle before loading or unloading.

•

Load and unload trailer on level ground.

•

Put manual transmission into first or reverse gear or automatic transmission into park. Turn off 
ignition. Set parking brake.

•

Block trailer wheels.

•

Incorrect loading can cause trailer swaying.

Rollover possible. If machine rolls over, you could be thrown from seat 

and killed or crushed. Wear seat belt.

*Always follow manufacturer instructions*

*AAA Rent-All 225-291-1356*

Summary of Contents for RT40






































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands