manualshive.com logo in svg

AAA RT40, Operator'S Manual

Share
Download
AAA RT40 Operator'S Manual Download Page 73

Trench - 72

RT40 Operator’s Manual

Setup

CMW

Setup

1.

Fasten and adjust seat belt.

2.

Start tractor. See page 58 for start-up procedures.

3.

Drive to starting point. Move in line with planned trench. See page 60 for operating procedures.

4.

Lower backfill blade.

5.

Engage parking brake.

6.

Lower boom to just above ground.

7.

Check that attachment speed/direction control and ground drive controls are in neutral.

8.

If equipped with combo, move selector valve to trenching position.

9.

Check that boom is in line with planned trench.

EMERGENCY SHUTDOWN - 

Turn ignition switch to STOP.

Crushing weight could cause death or serious injury. Use proper 

procedures and equipment or stay away.

NOTICE: 

Use attachments or counterweights to make front and rear loads balance when all 

attachments are raised. Contact your Ditch Witch dealer about counterweighting for your equipment. 

Jobsite hazards could cause death or serious injury. Use 

correct equipment and work methods. Use and maintain proper safety 
equipment.

NOTICE: 

Comply with all utility notification regulations before digging or drilling.

Incorrect procedures can result in death, injury, or property damage. 

Learn to use equipment correctly.

*Always follow manufacturer instructions*

*AAA Rent-All 225-291-1356*

Summary of Contents for RT40






































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands