AAA RT40 Operator'S Manual Download Page 91

Page: 91 / 165

Backhoe - 90

RT40 Operator’s Manual

Setup

CMW

Setup

Move attachment speed/direction control to neutral position.

Move ground drive control to neutral position.

Engage parking brake if not on level ground.

Lower rear attachment to 6” (150 mm) above
ground.

Check that backfill blade is straight and lower it to
ground.

Decrease engine speed to low throttle.

Move to backhoe operator’s station.

Release seat lock (shown) and move seat into
operating position.

Lower stabilizers enough to lift front tires.

10. Disengage stow lock.

11. Adjust engine speed to 1/2 to 3/4 throttle for

digging.

NOTICE:

Engine speed affects speed of backhoe operation.

t14om084h.eps

*Always follow manufacturer instructions*

*AAA Rent-All 225-291-1356*

Summary of Contents for RT40






































































































































































Search results

Summary of Contents for RT40

Reviews:

Related manuals for RT40

Brands by name

Popular brands

AAA RT40, Operator'S Manual

Search results

Summary of Contents for RT40

Reviews:

Related manuals for RT40

Brands by name

Popular brands