AAA RT40 Operator'S Manual Download Page 69

Page: 69 / 165

Transport - 68

RT40 Operator’s Manual

Haul

CMW

Unload

Lower trailer or ramps.

Remove chains from tiedowns.

Fasten and adjust seat belt.

Start tractor. See page 58 for proper start-up procedures.

Raise attachments, but keep them low and centered.

Disengage parking brake.

Slowly back unit down trailer or ramps.

Crushing weight. If load falls or moves it could kill or crush you. Use

proper procedures and equipment or stay away.

NOTICE:

•

Attach trailer to tow vehicle before loading or unloading.

•

Load and unload trailer on level ground.

•

Put manual transmission into first or reverse gear or automatic transmission into park. Turn off
ignition. Set parking brake.

•

Block trailer wheels.

•

Incorrect loading can cause trailer swaying.

Rollover possible. If machine rolls over, you could be thrown from seat

and killed or crushed. Wear seat belt.

*Always follow manufacturer instructions*

*AAA Rent-All 225-291-1356*

Summary of Contents for RT40






































































































































































Search results

Summary of Contents for RT40

Reviews:

Related manuals for RT40

Brands by name

Popular brands

AAA RT40, Operator'S Manual

Search results

Summary of Contents for RT40

Reviews:

Related manuals for RT40

Brands by name

Popular brands