manualshive.com logo in svg

AAA RT40, Operator'S Manual

Share
Download
AAA RT40 Operator'S Manual Download Page 60

RT40 Operator’s Manual

Drive - 59

Start Unit

CMW

1.

Fasten and adjust seat belt.

2.

Check that ground drive control and attachment speed/direction control are in neutral.

3.

Move throttle to idle.

4.

Verify that parking brake is engaged.

5.

Turn ignition switch to the run position (key on, engine off). Cold start wait indicator will light.

6.

When cold start wait indicator goes off, turn ignition switch all the way clockwise to start tractor. 
Warning alarm will sound. Indicators will light.

•

If engine does not crank, check start interlock display. See page 25 for start interlock information.

•

If engine turns but does not start within 10 seconds, allow starter to cool before trying to start 
again.

7.

Run engine at half-throttle or less for five minutes before operating tractor. During warmup, check that 
all controls work properly.

Improper control function could cause death or serious injury. If 

control does not work as described in instructions, stop machine and have it 
serviced.

NOTICE: 

Machine will not start if start interlock requirements are not met. See page 25 for start 

interlock information.

*Always follow manufacturer instructions*

*AAA Rent-All 225-291-1356*

Summary of Contents for RT40






































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands