manualshive.com logo in svg

AAA RT40, Operator'S Manual

Share
Download
AAA RT40 Operator'S Manual Download Page 79

Plow - 78

RT40 Operator’s Manual

Setup

CMW

Setup

EMERGENCY SHUTDOWN - 

Turn ignition switch to STOP.

Crushing weight could cause death or serious injury. Use proper 

procedures and equipment or stay away.

NOTICE: 

•

Plow will swing freely in float.

•

Keep everyone at least 6’ (2 m) from machine, attachments, and their range of movement.

Jobsite hazards could cause death or serious injury. Use 

correct equipment and work methods. Use and maintain proper safety 
equipment.

NOTICE: 

Comply with all utility notification regulations before digging or drilling.

Incorrect procedures can result in death, injury, or property damage. 

Learn to use equipment correctly.

NOTICE: 

•

Use attachments or counterweights to make front and rear loads balance when all attachments are 
raised. Contact your Ditch Witch dealer about counterweighting for your equipment.

•

Do not operate vibrator unless plow is in the ground.

*Always follow manufacturer instructions*

*AAA Rent-All 225-291-1356*

Summary of Contents for RT40






































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands