A-Neu Video ANI-4KANA Page 60 Instruction Manual Download

Page: 60 / 68

anapat SOFTWARE

RENAME:

Renames the currently selected

“Write to:”

EDID to the text typed into the

entry box.

PRE-F:

Opens a quick-access list of recently opened EDID files.

OPEN:

Loads a previously saved EDID file

(*.bin format)

from the local PC/Laptop and

places it into the left window.

WRITE:

Writes the EDID from the left window to the EDID destination selected in the

“Write to:”

dropdown menu.

READ:

Reads the EDID from the currently selected source/sink listed in the

“Read

from:”

dropdown menu and places it into the right window.

COMPARE:

Compares the EDID in the left window with the EDID in the right window.

Any data that is different between the EDIDs will be marked in red.

<= COPY:

Copies the EDID in the right window to the left window.

COPY SINK:

Allows directly copying the EDID from the current HDMI sink to any of the

Copy EDID slots.

ANALYZE:

Generates a short analysis report for the EDID (from the left or right window,

depending on the button pressed) in a new window. The report may be saved to the local

PC/Laptop if desired.

SAVE:

Saves a copy of the EDID (from the left or right window, depending on the button

pressed) to a file on the local PC/ Laptop.

CLEAR:

Clears the copy of the EDID (from the left or right window, depending on the

button pressed) from memory.

RX EDID:

Allows selection of any EDID stored in the unit, or copied from a connected

sink. The selected EDID will be set as the EDID to be sent to any device connected to the

HDMI input (Rx) of the unit.

Summary of Contents for ANI-4KANA





































































Search results

Summary of Contents for ANI-4KANA

Reviews:

Related manuals for ANI-4KANA

Brands by name

Popular brands

A-Neu Video ANI-4KANA, Instruction Manual

Search results

Summary of Contents for ANI-4KANA

Reviews:

Related manuals for ANI-4KANA

Brands by name

Popular brands