A-Neu Video ANI-4KANA Instruction Manual Download Page 20

Page: 20 / 68

RS-232 Protocol & Telnet Commands

COMMAND

DESCRIPTION

$HDCP_IN_SW?

Display the current HDCP support setting for the unit’s HDMI

input.

$HDCP_IN_VER

Set the HDCP version to use on the unit’s HDMI input.

Available values for

V1.4

[Supports HDCP v1.4 only]

V1.4+V2.2 [Supports HDCP v1.4 & v2.2]

NOTE:

Affects Analyzer mode only.

$HDCP_IN_VER?

Display the current HDCP version used on the unit’s HDMI input.

$HDCP_OUT_SW

Enable or disable HDCP support on the unit’s HDMI output.

= ON, OFF

NOTE:

Affects Pattern mode only.

$HDCP_OUT_SW?

Display the HDMI output’s HDCP status. A status of

“Talk”

means HDCP is currently performing handshaking.

$HDCP_OUT_VER

Set the HDCP version to use on the unit’s HDMI output.

Available values for

V1.4

[Output encrypted with HDCP v1.4]

V2.2

[Output encrypted with HDCP v2.2]

NOTE:

Affects Pattern mode only.

$HDCP_OUT_

VER?

Display the current HDCP version for the output port.

$HDR_EOTF N1

Set the HDR EOTF (Electro-Optical Transfer Function) mode.

Available values for

SDR

[Traditional Gamma, SDR Luminance Range]

HDR

[Traditional Gamma, HDR Luminance Range]

2084

[SMPTE ST 2084]

RSVD [Reserved for future use]

$HDR_EOTF?

Display the current HDR EOTF mode.

$HDR_MCLL N1

Set the maximum HDR content light level.

= 0~65500 [Incremented in 100 unit steps]

$HDR_MCLL?

Display the current maximum HDR content light level.

$HDR_MFALL N1

Set the maximum HDR frame-average light level.

= 0~65500 [Incremented in 100 unit steps]

$HDR_MFALL?

Display HDR maximum light level of frame-average.

Summary of Contents for ANI-4KANA





































































Search results

Summary of Contents for ANI-4KANA

Reviews:

Brands by name

Popular brands

A-Neu Video ANI-4KANA, Instruction Manual

Search results

Summary of Contents for ANI-4KANA

Reviews:

Brands by name

Popular brands