A-Neu Video ANI-4KANA Instruction Manual Download

Page: 8 / 68

Supported Color / AUDIO Formats

Supported Color Formats

RGB

YCbCr

4:4:4

YCbCr

4:2:2

YCbCr

4:2:0

Output

Resolution (Hz)

10 12

640x350p@

85~2048x1080p

@60

ü ü ü ü ü ü ü

3840x2160p

@23~30

* *

4096x2160p

@23~30

3840x2160p

@50~60

* *

4096x2160p

@50~60

NOTE:

= Specified color depth is supported;

= Specified color depth is supported &

TMDS scrambling is active.

Supported Audio Formats

Audio Source

Sampling

Rate (kHz)

Channels

Word Length

(Bits)

SD0~3 L/R Freq

(Hz)

HDMI Input

Bypass

Analog Input

2.0

16, 20, 24

Bypass

2.0

192

2.0

Internal

Sinewave

2.0, 5.1, 7.1

16, 20, 24

Mute, 200 ~ 1600

2.0, 5.1, 7.1

192

2.0

•

48kHz supports a maximum of (2) channels at 2048x1080p@29/30Hz resolution.

•

96kHz supports a maximum of (2) channels at 480i, 576i, 480p, 576p,

640x480p@59Hz, 720x400p@70Hz, 1280x768p@60Hz (RB), 1366x768p@60Hz

(RB), 2048x1080p@29/30/59/60Hz, 4096x2160p@29/30Hz resolutions.

•

192kHz is not supported at 1366x768p@60Hz (RB) or 2048x1080p@29/30Hz

resolution.

Summary of Contents for ANI-4KANA





































































Search results

Summary of Contents for ANI-4KANA

Reviews:

Related manuals for ANI-4KANA

Brands by name

Popular brands

A-Neu Video ANI-4KANA, Instruction Manual

Search results

Summary of Contents for ANI-4KANA

Reviews:

Related manuals for ANI-4KANA

Brands by name

Popular brands