A-Neu Video ANI-4KANA Page 49 Instruction Manual Download

Page: 49 / 68

Test PATTERNS

33. GRAYSCALE H

The

Grayscale H

pattern provides (4) distinct gray fields in an “H”

arrangement for testing luminance transition stability. No color or

interference should be visible at the transitions between sections.

34. GRID

The

Grid

pattern provides a selection of red, green, blue and white

boxes with 2x2 grids within and above them to test for pixel on pixel

and color offset issues.

35. IMAGE (2 VARIATIONS)

The

Image

pattern is a user customizable test pattern that holds (2)

bitmap images. One image is for use with low output resolutions (below

1920x1080) and the other is for high output resolutions (1920x1080

and above). The low resolution image is a 640x480 bitmap (RGB,

24-bit) and the high resolution image is a 1920x1080 bitmap (RGB,

24-bit).

NOTE:

To upload new images into the unit please the new replacement

image on a USB thumb drive with the ﬁle named

“IMG_480.BMP”

“IMG_1080.BMP”

as appropriate. Plug the USB thumb drive into the

USB port on the unit and navigate to the

“Setup”

menu. Next, activate

the

“Image 640x480 Update”

“Image 1920x1080 Update”

menu

item, as appropriate, to copy the new image to the unit.

36. LETTER H (2 VARIATIONS)

The

Letter H

pattern is a screen filled with a series of large capital

“H”

characters moving vertically up the screen. This is a basic test to

confirm motion detail. There are (2) variations: Large

“H”

characters

and small

“H”

characters.

37. LINE ON/OFF-H

The

Line ON/OFF-H

pattern generates an alternating pattern of

single-pixel horizontal white lines. This pattern can be used to analyze

the vertical pixel resolution of your display. If the output appears to

have mosaic patterns, or appears to be a solid gray field, then it is

possible that your display does not fully support the resolution you are

currently sending to it.

38. LINE ON/OFF-V (2 VARIATIONS)

The

Line ON/OFF-V

pattern generates an alternating pattern of single-pixel vertical

lines. This pattern can be used to analyze the horizontal pixel resolution of your display.

Summary of Contents for ANI-4KANA





































































Search results

Summary of Contents for ANI-4KANA

Reviews:

Related manuals for ANI-4KANA

Brands by name

Popular brands

A-Neu Video ANI-4KANA, Instruction Manual

Search results

Summary of Contents for ANI-4KANA

Reviews:

Related manuals for ANI-4KANA

Brands by name

Popular brands