A-Neu Video ANI-4KANA Instruction Manual Download

Page: 17 / 68

RS-232 Protocol & Telnet Commands

COMMAND

DESCRIPTION

$AUDIO_SR?

Display internal audio output sampling rate.

$AUDIO_VOL N1

Set the audio output volume.

= 0~80

$AUDIO_VOL?

Display the current audio output volume.

$BOOT GO

Reboot the unit.

NOTE:

The unit won’t respond to any commands during the boot

process.

$BOOT?

Display the current boot state.

$COLOR_SPACE

Set the output color space.

Available values for

RGB

[RGB 4:4:4] Y444

[YCbCr 4:4:4]

Y422

[YCbCr 4:2:2] Y420

[YCbCr 4:2:0]

$COLOR_SPACE?

Display the current output color space.

$DEEP_COLOR N1

Set the output color bit depth.

= 8, 10, 12

$DEEP_COLOR?

Display the current output color bit depth.

$EDID_COPY_

SINK N1

Copy the current HDMI sink’s EDID to the designated copy slot.

= C1~C10

NOTE:

If the copy fails

“$err”

will be displayed.

$EDID_MANUF?

Display the manufacturer name stored in the EDID of the

selected location.

Available values for

[HDMI Input (Rx) Port]

SINK_H [HDMI Sink]
SINK_V [VGA Sink]

NOTE:

•

If the EDID fails to be read,

“$err_ddc”

will be displayed.

•

If the EDID has invalid content,

“$err_bad”

will be displayed.

$EDID_MODEL?

Display the model/monitor name stored in the EDID of the

selected location.

Available values for N1:

[HDMI Input (Rx) Port]

SINK_H [HDMI Sink]
SINK_V [VGA Sink]

Summary of Contents for ANI-4KANA





































































Search results

Summary of Contents for ANI-4KANA

Reviews:

Related manuals for ANI-4KANA

Brands by name

Popular brands

A-Neu Video ANI-4KANA, Instruction Manual

Search results

Summary of Contents for ANI-4KANA

Reviews:

Related manuals for ANI-4KANA

Brands by name

Popular brands