A-Neu Video ANI-4KANA Instruction Manual Download Page 9

Page: 9 / 68

OPERATION CONTROLS & FUNCTIONS

TOP PANEL

OLED SCREEN:

Displays the current signal analysis information or test pattern mode

selection details including input and/or output resolution timing. The screen layout changes

depending on the unit’s mode.

ANALYZER MODE (Analyzer/Pattern button is

RED):

In Analyzer mode, if there is no live video

source detected on the input port, the OLED will

display any voltage, TMDS or sync that might be

present. Once a live video signal is detected, the unit

will display that signal’s current timing, format, HDCP

version, AV Mute status, color space, color depth and

audio format.

PATTERN MODE (ANALYZER/PATTERN BUTTON

IS BLUE):

In Pattern mode, when the output isn’t

connected to a sink, the unit will display the current

output timing, RxSense and Hot-plug detection

status. Once an active sink has been connected, the

lower portion of the display will change to indicate the

current test pattern number and name.

IR WINDOW:

Accepts IR signals from the included IR remote for control of this unit only.

MENU:

Press to enter the OSD menu or to back out from menu items.

Summary of Contents for ANI-4KANA





































































Search results

Summary of Contents for ANI-4KANA

Reviews:

Brands by name

Popular brands

A-Neu Video ANI-4KANA, Instruction Manual

Search results

Summary of Contents for ANI-4KANA

Reviews:

Brands by name

Popular brands