A-Neu Video ANI-4KANA Instruction Manual Download Page 25

Page: 25 / 68

RS-232 Protocol & Telnet Commands

COMMAND

DESCRIPTION

$SOURCE_

DETECT? N1

cont’d

VSI [Display packet-VSI data]
SCDC_SCR_ENABLE [Rx SCDC source enable scrambling state]
SCDC_SCR_STATUS [SCDC sink scrambling status]
SCDC_SINK_VER [SCDC sink version]
SCDC_SOURCE_VER [SCDC source version]

$TASK_MODE N1

Set the unit’s operation mode to Signal Analyzer or Pattern

Generation.

= ANALYSER, PATTERN

$TASK_MODE?

Display the unit’s current operation mode.

$TIMING N1

Select the output resolution timing to use.

Available values for

1~87

[All available standard output resolutions]

[Bypass (Analyzer mode only)]

$TIMING?

Display the unit’s current output resolution timing by timing

number.

$TIMINGX?

Display the unit’s current output resolution timing by timing

name.

$TMDS_FORMAT

Set the TMDS output format.

= HDMI, DVI

$TMDS_FORMAT?

Display the current TMDS output format.

$TMDS_SW N1

Enable or disable TMDS output.

= ON, OFF [Off will disable all video output]

$TMDS_SW?

Display the current TMDS output status.

$TX_5V N1

Set the unit’s 5v pin state to follow the TMDS output

state or to always be on.

Available values for

FOLLOW [Only outputs 5v if there is a live signal]
ON

[Always outputs 5v]

$TX_5V?

Display the current 5v pin setting.

$UPDATE_FW

Update firmware from USB & reboot the unit.

$UPDATE_

IMG1080

Update the 1920x1080 image from USB & reboot the unit.

$UPDATE_IMG480

Update the 640x480 image from USB & reboot the unit.

Summary of Contents for ANI-4KANA





































































Search results

Summary of Contents for ANI-4KANA

Reviews:

Brands by name

Popular brands

A-Neu Video ANI-4KANA, Instruction Manual

Search results

Summary of Contents for ANI-4KANA

Reviews:

Brands by name

Popular brands