A-Neu Video ANI-4KANA Page 23 Instruction Manual Download | Manualshive

Page: 23 / 68

background image

RS-232 Protocol & Telnet Commands

COMMAND

DESCRIPTION

$RX_SCDC N1

Enable or disable the SCDC port function on the HDMI input

(Rx).

N1

= ON, OFF

$RX_SCDC?

Display the current SCDC port state for the HDMI input (Rx).

$RX_SENSE N1

Enable or disable the RxSense function for the HDMI input (Rx).

N1

= ON, OFF

$RX_SENSE?

Display the current RxSense state for the HDMI input (Rx).

$SINK_DETECT?

N1

Displays a variety of sink detection status and informational

values.

Available values for

N1

:

HOTPLUG [Sink’s hot plug status]
RSENSE [Sink’s RxSense status]
HDCP [Sink’s HDCP port status]
HDCP_AKSV [Source HDCP AKSV in 2-digit hex (HDCPv1.4)]
HDCP_BKSV [Rx HDCP BKSV in 2-digit hex (HDCPv1.4)]
HDCP_RXID [Rx Receiver ID in 2-digit hex (HDCPv2.2)]
SCDC [SCDC port status]
SCDC_SCR_ENABLE [Rx SCDC source scrambling setting]
SCDC_SCR_STATUS [SCDC sink scrambling status]
SCDC_SINK_VER [SCDC sink version]
SCDC_SOURCE_VER [SCDC source version]

$SOURCE_

DETECT? N1

Displays a variety of source detection status and informational

values.

Available values for

N1

:

5V [5V detection state]
CKDT [TMDS clock detection]
TMDS_FORMAT [Detected TMDS format (DVI or HDMI)]
SCDT [TMDS sync detection]
HDCP [Source HDCP status detection]
HDCP_AKSV [Source AKSV in 2-digit hex (HDCPv1.4)]
HDCP_BKSV [Rx BKSV in 2-digit hex (HDCPv1.4)]
HDCP_RXID [HDCP Receiver ID in 2-digit hex (HDCP v2.2)]

HA [Horizontal active pixels]
HBP [Horizontal back porch pixels]
HFP [Horizontal front porch pixels]

21

«
...
21
22
23
24
25
...
»

Summary of Contents for ANI-4KANA





































































Reviews:

No comments

Related manuals for ANI-4KANA

Brand: Yamaha Pages: 3

Brand: F.W. Bell Pages: 75

Brand: ICS Pages: 2

Brand: CAISSON Pages: 5

Brand: R.M. Young Pages: 2

IEM-100 Beltpack

Brand: DAPAudio Pages: 19

Brand: YOKOGAWA Pages: 53

Brand: ICS Schneider Messtechnik Pages: 40

Brand: AR Pages: 8

Brand: Yamaha Pages: 8

Brand: Keller Pages: 8

iTrans 77023554

Brand: Industrial Scientific Pages: 94

Brand: Caen Pages: 63

Brand: Caen Pages: 35

Brand: Elcontrol Pages: 7

Brand: Omega Pages: 4

Combo meter P700 Pro

Brand: AquaMaster Pages: 20

Brand: Keysight Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands